Sale!

wereproudoftreatingeachclientasiftheywereamemberofthefamilyhelpingcustomerslocateelite1500plugnplayadaptorharnesskitforhondas2000haltechisourgoal0.jpg

Elite 1500 + Plug’n’Play Adaptor Harness Kitfor Honda S2000 Haltech

Original price was: $ 2.039,00.Current price is: $ 509,75.

SKU: mode_6565035835459 Category: Elite 1500 ECU + Plug'n'Play Adaptor Harness Kit Tags: Electrical, Elite ECU Plug'n'Play Adaptor Harnesses, Honda S2000, Honda/Acura, Page 2, Wiring Harnesses

Description
shopping

SUITS: Honda S2000 AP1 (00-04), AP2 (05), non DBW, manual transmission only.

INCLUDES: Elite 1500 ECU, Plug’n’Play adaptor harness, M14 x 1.5 air temp sensor with matching plug and pins, auxiliary I/O 16 Pin TYCO plug and pins, USB programming cable and USB software key.

NOTES: Product does not support the following OEM Functionaliy Immobiliser Fuel Tank Pressure Sensor K-Line Communication Start Switch Signal Air Pump Electric Current Sensor

OVERVIEW

ADAPTOR OVERVIEW

This adaptor plugs directly into your Haltech Elite ECU and has a set of factory connectors on the other side which plug straight into the factory harness. A quick and easy plug’n’play upgrade solution.

A simple Haltech Plug’n’Play product that allows plugs directly into your car’s factory harness.
The quick start guide will walk you through installation of the Haltech Plug’n’Play adaptor into your vehicle.

When purchased as a kit with a Haltech ECU, this product is accompanied by the full ECU manual and Software located on the CD or USB key.

ECU OVERVIEW

Featuring a robust, environmentally sealed waterproof case, drive by wire throttle control, intake and exhaust cam control, short term and long term map learning, knock control, and much more, the Elite 1500 ECU provides engine calibrators the tools they need to get the job done right. Alongside the Elite 1500 ECU is the Elite Software Programmer (ESP) that brings levels of functionality and user friendliness never seen before in an engine control package. Together they offer true cutting edge technology to tuners and performance enthusiasts worldwide.

Supports 1 to 12 cylinder engines
2 rotor engines
Normally aspirated or forced induction
Load sensing by Throttle Position (TPS), Manifold Absolute Pressure (MAP) or Mass Air Flow (MAF)
Staged, sequential, semi sequential, batch or multipoint injection patterns
Distributor ignition systems, multi-coil systems, expand CDI range or Haltech Multiplex CDI systems
Connect to a wide range of display dashes and expansion devices via CAN.
4 x fuel injection outputs
4 x ignition outputs

12 x digital outputs
10 x analogue voltage inputs
4 x synchronised pulsed inputs
3 x dedicated inputs (knock, ignition switch & onboard MAP Sensor)
2 x dedicated engine position inputs with extensive trigger type support
Up to 45 channels of Input & Output (I/O) expansion (via CAN)
USB laptop communication (Windows)
ESP Calibration Software – intuitive and easy to use

FEATURES

SUPPORTED OEM FUNCTIONALITY:

Idle Control (BAC)
Thermofan
Tachometer
A/C Request and Control
Engine Control Relay
Fuel Pump
Electrical Power Steering Load Detect
Knock Sensor 1
Coolant Temperature Sensor
Air Temperature Sensor
O2 Sensor Front & Rear
Check Engine Light
Throttle Position Sensor
Vehicle Speed Sensor
VTEC Oil Pressure Switch
VTEC Solenoid
Air Pump Relay (E1500 Only)
Factory Map Sensor
Alternator Control
Brake Pedal Switch
Electrical Load Detect
S2000 Coolant Gauge

ECU FEATURES

Drive by Wire Throttle Control (DBW).
Low Impedance Injector control with programmable injector peak and hold currents and programmable peak time.
Flex fuel support (Direct sensor input). Tune your engine’s boost, fuel and ignition by ethanol content.
Flexible tuning setup for Petrol (Gasoline), Methanol and Ethanol.
Closed Loop 02 Control. Dual bank control for precise tuning (with optional external CAN O2 Wideband Controller Kit).
Knock Control. Synchronised to engine position with high speed digital filtering for accurate detection.
Variable cam control – Independently control up to 4 camshafts.
Closed Loop Idle Speed Control with learning for consistent idle stability.
Long term learning (auto tune) on fuel, ignition, cam, boost and idle control maps (up to 4D).
On-board data logging. Up to 40 channels of logging at sample rates up to 5ms (200Hz) with 2MB of internal memory.
Laptop data logging. DLog all available channels directly to your laptop’s hard drive for both tuning and diagnostics.
Dual CAN Bus communication for Haltech dashes and expansion devices. Supports OEM CAN and OBDII. View live engine data and set/clear diagnostic trouble codes.
1 – 4 Injection stages with individual injector flow rates per injector.
Anti-Lag/Rotational idle for closed course racing, rally, circuit or drift. Build and maintain boost during closed throttle conditions.
Rolling Anti-Lag. Lock to your current or pre-set RPM or road speed for roll racing or pit lane limiting.
Launch Control. Control your engine’s power delivery, RPM and boost for consistent performance at the start line.
Traction Control. Control your engine’s power output via mappable front vs rear axle or individual wheel speed slip.

ADVANCED TUNING

Tuning table resolution up to 32 x 32 x 8
Limitless tuning flexibility. Tune your engine by a combination of 4D tuning tables combined with 3D per cylinder compensations and multiple user-definable corrections.
Per Cylinder Tuning Correction – 3D
Wideband O2 Control. Connect up to 9 channels via CAN expansion devices.
Thermocouples/EGT (Exhaust Gas Temperature). Connect up to 12 channels via external CAN expansion devices.
Advanced Engine Protection. Set multi-level limits for sensors and protect your engine against common causes of failure.

RACE FUNCTIONS

Nitrous control with advanced programming of up to 6 stages of wet or dry nitrous kits with on/off delays and banked control options. 3D fuel and ignition corrections for all stages.
Boost control. Intelligent 4D closed loop learning with flexible, user-definable axis and 14 fully user-definable corrections.
Sequential turbo control
CO2 boost control. Wastegate pressure and position, intake air bleed control (charge pipe wastegate) functionality for the hard-core racer.
Flat shifting. Optimise your shifting precision via a combination of inputs such as a clutch switch or strain gauge.
Shock Travel/Ride Height inputs allow dynamic tuning and data logging to assist in chassis development and power delivery.
Timer functions. Use the combination of the race timer and 5 additional programmable timers for time-based control of multiple engine parameters, power delivery and other user definable functions.
Trans brake function allows smooth and consistent control of start line staging (Bump or Creep).

Prompt Shipping and Professional Packing

We offer a wide range of shipping options owing to our long-standing partnerships with UPS, FedEx and DHL. Our warehouse staff are highly trained and will pack the goods according to our precise and exact specifications. The goods you send us are checked thoroughly and secured properly prior to shipping. Everyday we deliver thousands of packages to customers from all over the world. This shows our commitment to become the biggest online retailer in the world. Warehouses and distribution centers are located in Europe and the USA.

Note: Orders that contain more than one item are assigned a particular processing period dependent on the particular item.

Prior to shipping Our team will conduct a thorough inspection on the items you purchased. Today, the majority orders will be shipped within 48 hours. Delivery time ranges between 3-7 days.

Returns

The stock market is always changing. It's not completely managed by us, as we have multiple parties such as the factory and the storage. The stock levels may fluctuate at any moment. Please understand it may happen that your order is out of stock after the order has been placed.

Our policy is valid for 30 days. If it's been longer than 30 days since the date you bought the item We're sorry to say that we can't offer you a full refund or exchange.

The item must not be in use and must be in its original condition. It should also be in the original package.